您当前的位置:  常见问题
  • 玻璃态转换温度, Glas transition temperature

    玻璃态转换温度(TG) 是胶水变脆时的温度。应用温度显然要高于胶水的玻璃态转换温度 (如 可重复揭开的袋子存储在冰箱里,可以防止袋子的重新闭合)


    The glass transition temperature (TG) is the temperature at which the adhesive becomes brittle. It is important that the application temperature is distinctly above the TG of the adhesive (e.g. resealable bags that are stored in the fridge or freezer as it can prevent a safe reclosure of the bag).

  • 硬胶, Hard adhesive















    Term usually used to characterize highly cohesive PSA tapes.

    Advantages (compared to soft adhesives):

    higher holding power withstands

    higher sustained loads good temperature resistance

    less edge picking

    improved die cuttability



    low initial tack and adhesion;

    requires higher contact pressure

    not suited for rough surfaces

  • 热熔压敏胶, Hot melt pressure-sensitive adhesive


    Types of pressure sensitive adhesive that can be coated without use of solvents or water. Today PSA tapes based on synthetic rubber as well as acrylics are available for hot melt coating.

  • 耐湿性, Humidity resistance


    Moisture or even humidity can affect the performance of an adhesive. Especially if applied under wet or very humid conditions the adhesive absorbs the humidity, which leads to reduced adhesion performance. This effect occurs especially with water-based acrylics, which should not be used under those conditions.


    In general a PSA tape is humidity resistant when it resists contact with humid air or even water without negative effects on the adhesion properties 


    All acrylics have a good humidity resistance. Humidity can damage paper liners and lead to “bubbles” on the surface of the tape. Basically, filmic liners are more dimensionally stable than paper ones.



  • 离型纸, liner


    1. 纸质离型纸(如 格拉辛纸, PE涂层纸, 粘土涂层纸)

    2. 塑料薄膜离型纸(如 聚丙烯,聚酯,聚乙烯) 硅被用作离型剂避免离型纸与胶水粘接在一起。


    Anti-adhesive material which covers the adhesive on almost all d/s and some s/s tapes and prevents the adhesive from sticking to itself. The liner is used as a protection aid during handling/processing and storage. Most commonly used liner types are

    1. Paper liners (e.g. Glassine paper, PE-coated paper, Clay-coated paper)

    2. Film liners (e.g. PP, PET, PE) Silicone is used as release system to avoid adhesion between liner material and adhesive.



  • 转移, migration



    The molecular movement over a long period of time of an ingredient from one surface to another when both are in contact. Migration may occur between tape components and the surface to which applied. Some plastic films (e.g. PVC) contain plasticizers which are apt to migrate into the tape adhesive, causing the adhesive to soften. Other ingredients like foaming, vulcanisation, age-resistant agents used for flexible seals migrate into the tape and can compromise the bond.

  • 非极性材料, Non-polar substrates


    Critical surfaces to adhere to due to low surface energy. The lower the surface energy the lower the molecular attraction to the adhesive (adhesion). Typical materials are polyolefins such as PP and PE, but also PS, EVA and many powder painted surfaces. By surface pretreatment (e.g. corona treatment) the polarity can be modified to achieve higher surface energy and improved adhesion. Use of primers will also act as adhesion promoters.

  • 挥发性, Outgassing

    化学成分从胶水中挥发出来(如单体残余物, 溶剂等)尤其在高温情况下。化学残余物可能出现的影响在汽车,航空和电子行业中经常是一个问题。 

    Amount of chemical ingredients evaporating from adhesives (e. g. monomer residues, solvents, etc.) especially under elevated temperature conditions. Often a concern in the Automotive, Aerospace and Electronics industries, where chemical residues could affect e. g. electric circuits.



  • 极性材料, Polar substrates

    因为高的表面能而相对容易粘接的表面。在这些被粘物上,在胶水和被粘物中间高的分子吸引力会增加粘接强度。最常见的材料有PET, PC, PVC, ABS,钢板,铝,玻璃等。

    Uncritical surfaces to adhere to due to high surface energy. On these substrates the high molecular attraction between adhesive and substrate leads to increased adhesion. Most common materials are PET, PC, PVC, ABS, steel, aluminum, glass etc.

  • 底涂剂, Primer


    A coating applied to a surface (e. g. backing or a substrate) prior to the application of an adhesive, improving bond performance between backing and adhesive or between tape and substrate